Cute ghost coloring pages

Published at Wednesday, 19 February 2020.

Masonry Walls and Ceilings. Interior masonry walls and ceilings above grade may, in general, be painted in much the same manner as plaster surfaces. Here again, it is necessary to allow adequate time for the masonry to dry before applying paint and, in addition, attention should be given to the preparation of the surface. When decorating a wall containing Portland cement (concrete, for example), it is essential to take precautions against the attack of alkali. For this purpose, alkali-resistant primers such as rubber-base paints may be used when oil paints are to follow. If you decide to do your own body work discuss it with the paint shop first. They'll probably have recommendations on the type of primer you use. Some brands will be more compatible with their primers or color coats. The rule of thumb is to stay within the same brand of paint, both for prep and color. Even the cheapest paint shops typically use a brand name on their intermediate and higher paint jobs. Find out what it is and use the same brand as your primer coat. This will ensure you don't create adhesion problems for yourself down the road. You can put it around a room and probably follow immediately with the finish coat. It can be applied with brush or roller.

What are the major color fields in the painting and their role in the entire composition? Is the light optically realistic or expressive as in Matisse's painting? The second part of preparation is surface prep, it addresses covering the surfaces you do not want to get any paint on. A little plastic sheeting will go along way to keeping paint off of floors, window coverings, handrails, cabinets, counter tops, etc... And, if you are not confident with your ability to paint a straight line next to door casing, baseboards, cabinets or hardware protect these surfaces using masking tape. There are two basic types of masking tape white/yellow and blue. The white tape sticks to surfaces better but, can pull off finishes on cabinets or stained woodwork. Blue tape usually will not pull off finishes but, does not stick as well, this will probably be the tape to use for most applications. Always wipe down or dust the surface you will be masking to assure the best tape adhesion possible. If you use blue tape you may need to re-rub down the tape before painting next to it, only mask off areas with blue tape that you will be painting for a given day. With either tapes, do not assume the are a force field that paint will not penetrate, use them as a reference and dry brush the paint next to the edge of the tape and avoid soaking the edge of the tape with a lot of paint, this will cause the paint to "bleed" through giving you an undesired look. If you will need to apply multiple coats of paint, on the first coat, paint as close to the tape as you can, not really getting paint on the tape. With the second coat or a one coat application, you can use the tape more of like a paint barrier and get a little more paint on the tape if you immediately remove each section of tape after painting the section, this will keep the paint from sitting on the tape and "bleeding" behind it. Also, if you get a lot of paint on the tape it is not good to let the paint dry on the tape because some paints (especially the glossier paints) will peel if allowed to dried, with the tape when it is pulled off. White tape should not be left on for longer than a couple of days and I suggest not leaving it on more than a day in areas that receive long periods of direct sunlight. Blue tape can be left on for days, if it will stay on, there again it does not stick as well and may need rubbed down again immediately before painting up next to it. For stippling you need a special brush; get one that is flat, and has short, stiff bristles. At a minimum you want to remove all the chrome from the car. Take off both front and rear bumpers. If your Mustang has bumperettes that are body color be sure to bring them along so they can get sprayed at the same time as the rest of the car. Remove all rocker, hood and trunk molding. Same for wheel well molding and all emblems. This would be a good time to order some new emblems and attachment hardware. Also spend some time cleaning up all the chrome with #0000 steel wool. Nothing looks worse on a fresh paint job then faded emblems and corroded, cloudy chrome.

Leave a Reply